CLEAR Coating Epoxy Resin 40L KIT

CLEAR Coating Epoxy Resin 40L KIT

gray stars

*** OUT OF STOCK **
Click Picture for more Info

Comes with 20L Resin and 20L Hardener

Wood, Bar & Counter Top coating resin, UV stable, Max pour 1/4 in or .250

 

Easy MIX 1 Part A : 1 Part B (by volume) 

Can$1,448.52
SKU 28229

Features Include:

  • Extremely durable finish, scratch resistant, heat resistant, requires no maintenance.
  • Will cure to a clear, glass-like finish.
  • High content of organic products.
  • Easy to use and low odor.
  • 100% solid rate.
  • Can be poured up to 1/4 "thick per coat or .250
  • 80lbs / 36kg

How much resin do I need?

 
#282 CLEAR Epoxy Resin can be applied with a foam brush/roller or squeegee. Material is typically applied in two stages:

In the first stage a thin layer of material is applied to seal the substrate and prevent any air bubbles from forming in future coats.

The second stage requires thicker flood coats applied at 1/8”. How many flood coats are needed depends on your particular application but one to three is typical.

Recoats can be applied as soon as current layer has “tacked up”. If your previous layer has fully cured then very light sanding with a fine grit (220) sandpaper followed by a solvent wipe (isopropyl alcohol or acetone) is necessary before application of subsequent layer. A heat gun or torch may be used after the pour is completed and the material is still liquid to burst/pop any remaining air bubbles. If a torch is used the flame should never come in direct contact with the epoxy, smooth strokes 6-12 inches above the material is all that is required. 

Work Time: 20 min

Gel Time: 30 min (150 grams)

Drying Time: varies on thickness but roughly 6-8hrs(surface) to 10-14hrs(Thru) to complete hardness in 5 days.

Application TIPS: Do not vary or deviate from mix ratios, failure to do so can result in soft spots or partial curing. For best results the material should be used at temperatures from 70°-80°F. Work areas should be clean and dust/insect free.

SAFETY PRECAUTIONS:

  • Mix and pour in a well-ventilated area.
  • Avoid contact with skin and eyes. If contact does occur, wash skin with soap and water and seek medical help.
  • Read and understand all CAUTIONS on container labels and safety data sheets before using this material.
  • Avoid breathing of vapors.
  • Forced local exhaust is recommended to effectively minimize exposure.
  • NIOSH approved, organic vapor respirators and forced exhaust are recommended in confined areas, or when conditions (such as heated polymers, sanding) may cause high vapor concentrations.

DO NOT WELD ON, BURN OR TORCH ON OR NEAR ANY EPOXY MATERIAL. HAZARDOUS VAPOR IS RELEASED WHEN AN EPOXY IS BURNED.


 Shipping Chemicals and  Wide Fabric Make it impossible to Calculate Shipping Costs in Advance.
Your trust is important so we only charge what shipping cost us.
 
Disclaimer: The information contained herein and provided by RAYPLEX LTD is considered accurate.
However, no warranty is expressed or implied regarding the accuracy of the data, the results to be obtained
by the use thereof, or that any such use will not infringe any patent. Before using, user shall determine
the suitability of the product for the intended use and user assumes all risk and liability whatsoever
in connection therewith.
 

CUSTOMER SERVICES

WEBSITE INFORMATION
RESOURCES

RAYPLEX LTD

Returns
Shipping 
Indian Status Tax Exemption

 

 

 

 

 
 

 

 

 
Copyright © 2022 Rayplex Ltd.  
RAYPLEX is a registered
Trade Mark All rights reserved. 
 
 
 
 
341 Durham Crt, Oshawa, ON L1J 1W8
Phone: 905-579-1433 Fax: 905-579-1431
Hours of Operation: Mon-Fri 9am-5pm
Email: sales@fibreglass.com